南京魯伯思特電子科技有限公司 

專利創新外觀 觸摸屏密碼鎖 夜視背光 豪華大氣   

一、  此密碼鎖有兩種使用方法

We have two ways to open the lock.

1、    鍵盤輸入開鎖

Enter the right code to open the lock.

有管理碼和用戶碼兩套密碼（都為1-8位），出廠密碼分別為1234和12345678

The lock’s factory default setting is 1234 and 12345678

  2、應急開鎖，出廠密碼12345678

    Emergency unlock ,the lock’s factory default setting is 88888888.

注意應急密碼必須跟其他的密碼不同。

Note : you has to make Emergency code different from Other codes.

二、管理碼和用戶碼的修改

   To change the management password code and user password

1、    修改管理碼:輸入管理碼（1－8位數字鍵）,按"#"鍵,綠燈亮, 在綠燈亮期間按“*”鍵，面板黃燈亮(超過8秒沒有任何輸入,則退出修改模式，進入待機狀態),進入修改密碼狀態，輸入新密碼后按"*"確認.聽到"滴滴滴",黃燈滅說明管理碼修改成功;聽到"滴滴滴滴",修改失敗,請重試。Management password changing :input the old code ,press “#”key ,the green LED will light ,at same time press “*”key the screen will have yellow light(if you do not do it more than 8 seconds ,it will abort changing state ,it’s going to waiting state.), it’s going to changing code state ,input the new code you want to change and then press “*”key to confirm .if you hear “deep” three time ,that means you change code successfully ,if not change again

2、    修改用戶碼: 輸入用戶碼（1－8位數字鍵）,按"#"鍵,綠燈亮, 在綠燈亮期間按“*”鍵，面板黃燈亮(超過8秒沒有任何輸入,則退出修改模式，進入待機狀態),輸入新密碼，按"*"確認.聽到"滴滴滴",黃燈滅說明修改成功;聽到"滴滴滴滴",修改失敗,請重試。

User password changing :input the old code ,press “#”key ,the green LED will light ,at same time press “*”key the screen will have yellow light(if you do not do it more than 8 seconds ,it will abort changing state ,it’s going to waiting state.), it’s going to changing code state ,input the new code you want to change and then press “*”key to confirm .if you hear “di” three time ,that means you change code successfully ,if not change again.

三、應急密碼修改

A、   修改應急密碼:在面板上輸入正確的管理碼或用戶碼,按"#"鍵,綠燈亮,進入開門狀態，在綠燈亮期間按“##”鍵，面板黃燈亮, 在8秒內通過鍵盤輸入新密碼，按"*"確認.聽到"滴滴滴",黃燈滅說明管理碼修改成功;聽到"滴滴滴滴",黃燈滅說明管理碼修改失敗,請重試。

Changing emergency code : Enter the management code or user code .then press the “#” button ,the green LED light ,the door are in opening sate .at the time when the green LED lights press the “##” key ,the yellow LED lights ,in the eight seconds input the new code ,the press the “*”key to confirm .when you hear three beeps ,the yellow LED turn off ,you change the code successfully .if you hear four beeps ,yellow LED turn off ,you changer the emergency code unsuccessfully .please do it again.

四、開門

   Unlock

1、    鍵盤輸入開鎖：輸入管理碼或用戶碼，按"#"鍵,綠燈亮，轉動把手開門。如果連續輸入錯誤密碼4次，則鍵盤鎖定，60秒后恢復正

Input one of right code(management code and user code) to open the door ,press “#” green LED lights ,if you input wrong code three time ,the keypad will lockautomatically , after 60 seconds it’s going to unlock automatically.     

2、   應急密碼開鎖：按"##"鍵,黃燈亮后, 通過鍵盤輸入應急密碼后按“＃”開鎖，聽到"滴滴",綠燈亮, 轉動把手開門,開鎖5秒后鎖自動閉合,綠燈滅。聽到"滴滴滴滴"綠燈不亮，開鎖失敗，請重試。如果連續4次輸入錯誤密碼，則鍵盤鎖定，60秒后恢復正常狀態。

      Using emergency code open the door :press “# ”key twice , yellow LED lights ,enter the emergency code ,then press the “#” key ,when you hear two beeps ,green LED lights, turn the handle ,the door keeps opening in five seconds ,the green LED turns off .If you hear four beeps ,the green LED does not light ,open the door unsuccessfully ,repeat the steps .If four incorrect codes are entered in a row ,the LOCK will shut down for a period of up one minute.

五、管理碼和用戶碼復位

Reset management code and user code

通過應急密碼開鎖后，復位管理碼和用戶碼為“1234”和“12345678”。

After unlock by emergency code ,recover the management code “1234”and user code “12345678”.

六、欠壓提示

   Low power notice

    當電子鎖處于開鎖狀態時，如果面板上的紅色指示燈亮，說明電池電壓已經過低，請及時更換新的電池，以確保電子鎖能正常工作。

 When you open the door you find the red and green LED light at same time , the voltage is very low ,you need to change the battery as soon as possible, four AA battery can be used many times to open the lock at this time .